110 Volt Micro-Controller Interface

Years ago, I built this controller to switch 110 volts with a printer port on my computer. I am adding a micro-controller so my computer will not be required in the greenhouse. Each one or all of the six A/C lines may be switched on or off.

Micro-controller On Test Bench

Test setup of a micro-controller controlling a 3/4 inch sprinkler valve. A transister is used to detect the 5 volt signal and turn on the 12 volts for the valve. Although the valve is rated at 24 volts, the actual voltage at the valve after running 50 to 100 feet of wire to the valves will be lower than 24 volts. These valves functioned very well with 12 volts. The transister is rated for 30 volts, so if required, a different power supply (wall wart) could be changed out.

This setup functions well, I am adding additional devices to be controlled by the micro-controller:

Additional valves - plant watering, mist control

3 volt fan - on when mist control valve is on

12 volt fan for outside air when required.

Watering Strawberry Plants

Strawberry plant being watered with an adjustable drip head. This device allows adjusting the amount of water delivered and it is set to just trickle. This allow more devices on the 1/4 inch hose, but it requires 4 minutes to deliver the amount of water required.

One thing to remember when using drip irrigation; you can lower the amount of water delivered and increase the time the valve is on to get the required amount of water to the plants.

Trees Watered With Drip Irrigation

Various plants will be watered when their zone is watered. I have one zone on my sprinkler system which only controls drip irrigation devices. This allows me to water using drip irrigation for a shorter length of time than I water the grass in the yard.

Extension Required To Install Drip Irrigation

This is a six inch extension which is needed when the sprinkler head is removed and a four or six drip hose adapter replaced a sprinkler head. Useful when an entire zone is for drip irrigation and used when the sprinkler device is replaced with multiple drip hose connector.

Sprinkler device & 1/4 hose

This adapter is installed between the sprinkler head and the sprinkler pipe allowing a single drip hose to be attached. Although it only feeds a single 1/4 inch line, it allows the sprinkler device to be re-attached. Disavantage is the 1/4 inch line is on for the full time the sprinkler device is on.

4 Hose Adapter For Drip Irrigation

This is a different type of drip adapter. It also will replace the sprinkler head. It allows four 1/4 inch drip hoses to be attached in place where the sprinkler head was removed. Again, the number of devices it will feed is determined by the type of attached devices. If the device has an adjustment, it may be turned down, which will enable additional devices to be attached.

Six Hose Adapter For Drip Irrigation

This adapter will replace the sprinkler head and allow six 1/4 inch drip hose to be attached. The water pressure is reduced and each connection can feed multiple watering devices. How many it is capable of feeding is determined by the amount of water each device meters out. Some devices allow adjustments, other don't have any adjustment.

Ocean Breeze Mist Device

The mister head in installed with wire ties. The support is 1/2 inch PVC pipe. I have a 3 volt fan mounted in a 3 inch PVC pipe which will blow the mist around the greenhouse. Should move enought air to avoid water on the leaves of the plants on the shelves. The Ocean Breeze kit cost under $25 and I have 7 mist devices left. One may be installed in the 4' x 4' greenhouse. Depends on how well it lowers the temperature without getting water on the plant leaves.

Plans are to pulse the mister on for 20 seconds, then off for two or three minutes. After installing the valve and controller, I will record the starting temperature, time on, time off, amount temperature is lowered and if there is water on the plant leaves. The time on and time off will be easy to modify. The valve is a standard yard sprinkler system device, and should cycle this often without any problem.

If there is a problem and the heat goes over the programed limit, the alert will enable me to see what the problem is and correct the problem (unless I am away from home). Plants die very quickly when it is hot. Dries up the soil, and the plants wilt!

Ocean Breeze Mist For Cooling

My first concern was the low over-night temperatures. A oil-filled heater on sale at Wal-Mart was purchased and a 20K BTU natural gas heater was ordered from Harbor Freight. My second concern was the peak daytime temperatures. I decided to use a water mist system to lower the temperature in the greenhouse .The Ocean Breeze kit contained 10 mist heads, I installed three in the top of the greenhouse.

Currently I open the vent and turn on the mist system manually. Within a couple of weeks I should have the embedded system tested and installed. It will monitor the temperature and controll the water to the Ocean Breeze and the fan. The vent will be self opening and closing using a standard greenhouse vent control.

In addition, I will have a 12 volt fan installed to vent the inside air. Additional devices will be added after testing on the bench.

6'x8' Master Gro Greenhouse

The 6' x 8' greenhouse blocks the view of the smaller 4' x 4' greenhouse. The instruction said to allow four to six hours to assemble, but it required the full six hours for us. The first evening we sorted the items and assembled the base. The next morning we completed the greenhouse just before lunch. A single item was missing and a call to the manufacture got that part on the way.